View MasonrySaver items  
     
 
  • Item: MasonrySaver Safer Brick & Masonry Cleaner
 
  SKU: SS37001  Q/A: data-sheet
 
 
  Size: Available in 1 gallon recyclable plastic containers
 
 
  Property Type: Muriatic acid equivalent
 
 
  Appearance: Straw colored clear liquid
 
 
  VOC Content: n/a g/L  
     
  Case Pack: 1-gallon; 6/case  
     
  Shelf Life: not stated  
     
  UPC Code: 7-09057-37001-1; 1-gallon
 
 
  Product Description  
     
 

MasonrySaver Safer Brick & Masonry Cleaner MasonrySaver® Safer Brick & Masonry Cleaner is a proprietary formulation of special acids and cleaners which effectively removes rust, mildew, algae, smoke, and creosote stains. It is a safer alternative to Muriatic acid, cleaning as good - with a special additive to reduce fumes and burns that are normally associated with Muriatic acid.

  • Eco-friendly
  • Low odor & Low fumes
  • Safer to use than Muriatic Acid
  • Cleans and etches like Muriatic Acid
  • Not likely to cause Acid Burns on skin
 
 
  MasonrySaver Safer Brick & Masonry Cleaner
 
 
 

MasonrySaver Safer Brick & Masonry CleanerWhere to Use:
Use MasonrySaver Safer Brick & Masonry Cleaner to clean both brick and masonry surfaces of rust, mildew, algae, smoke, and creosote stains. MasonrySaver Safer Brick & Masonry Cleaner can also be used when acid etching prior to applying floor coatings.

Application:
Brush surfaces to be cleaned with a stiff brush to remove loose particles. Wet all surfaces to be cleaned with liberal amounts of water. Flood the surface with MasonrySaver Safer Brick & Masonry Cleaner taking care that the product does not run down onto non-targeted areas. Using a stiff, non-metal brush, scrub the area thoroughly, allowing the cleaning solution to remain on the area for three to five minutes. Completely rinse the treated area using a garden hose with adjustable nozzle, or pressure washer set at 400-600 psi. When rinsing, use as much water as possible. To avoid streaking rinse from the bottom up. For severely stained areas it may be necessary to repeat the application of MasonrySaver Safer Brick & Masonry Cleaner.

Limitations:
Do not use on limestone as MasonrySaver Safer Brick & Masonry Cleaner will dissolve it.

What are the Coverage Rate(s):
40 - 80 sq. ft. depending on surface porosity.

Dilution Ratio:
Dilute MasonrySaver Safer Masonry Cleaner 1:4 with water. For difficult to remove stains the product can be used at full strength.

Equipment:
Stiff non-metal brush and a garden hose with adjustable nozzle; or pressure washer set at 400-600 psi. Pump-up Sprayer.

Safety Precautions to Observe:
Proper safety procedures should be followed at all times while handling the product. Wear chemical resistant gloves and chemical splash goggles. 

Refer to the Material Safety Data Sheet for important health and safety information before use.

 
  Worth Quoting...  
     
 

" This formulation of special acids and cleaners will effectively remove rust from concrete, green algae on brick sidewalks, efflorescence brick, along with mildew, smoke and creosote stains. The chemical composition of Safer Masonry Cleaner is the same as Muriatic Acid with proprietary additives. "

 
Copyright (c) 2002 - 2014 Small's Hardware Inc. All rights reserved. Privacy Notice | Contact Us
All trademarks and registered marks are the property of their respective owners.
DTEP is a registered trade name of Small's Hardware Inc. State of Ohio
Mailing Address • 109 S Wayne Ave • Lockland OH • 45215
Visit our StoreFront