View MasonrySaver items  
     
 
  • Item: MasonrySaver Decorative Concrete Sealer
 
  SKU: SS31011  Q/A: data-sheet
 
 
  Size: Available in 1 and 5 gallon recyclable containers.
 
 
  Property Type: Proprietary Waterborne Emulsion
 
 
  Appearance: Opaque, low odor.
 
 
  VOC Content: Less than 50 g/l  
     
  Case Pack: 1-gallon; 6/case
Case Pack: 5-gallon
 
     
  Shelf Life: 18 months in original unopened container.  
     
  UPC Code: 7-09057-31011-6; 1-gallon
UPC Code: 7-09057-31059-8; 5-gallon
 
 
  Product Description  
     
 

MasonrySaver Decorative Concrete Sealer is a non-yellowing acrylic polymer blend sealer formulated for use on properly cured stamped concrete surfaces. Designed for use on both interior and exterior concrete, MasonrySaver Decorative Concrete Sealer is suitable for use on a variety of surfaces where a durable gloss finish is desired including concrete patios, driveways, sidewalks and even garage floors.

  • Water-based formula for easy application and rapid dry time.
  • Provides an attractive, gloss finish to stained concrete.
  • Protects stained concrete surfaces from color fade.
  • Seals concrete surfaces making them washable and easy to maintain.
  • Non-yellowing, clear finish.
  • Durable concrete protection with "hot tire" resistance.
  • Can be applied over previously treated surfaces with solvent-base sealer.
 
 
  MasonrySaver Decorative Concrete Sealer
 
 
 

MasonrySaver Decorative Concrete SealerWhere to Use:
MasonrySaver Decorative Concrete Sealer dust proofs concrete with a durable acrylic blend resin. On surfaces that have been previously stained using MasonrySaver No-Rinse Acid Etching Stain, MasonrySaver Decorative Concrete Sealer leaves an attractive, non-yellowing durable gloss finish that protects concrete from damage and color loss due to ultra-violet light, moisture and abrasion/wear.

Mixing:
Material may separate during long-term storage so mix thoroughly before use.

Application:
Apply two uniform coats of material to new, previously untreated concrete surfaces. Allow the first coat of material to dry sufficiently to walk on, but not more than 4 hours, prior to application of the second coat. MasonrySaver Decorative Concrete Sealer may be sprayed applied using a pump-up, “garden type” sprayer with fan type nozzle, with an airless industrial sprayer or by roller. If roller applied, use a short nap cover. Avoid puddling or ponding of product: brush or roll material until it thoroughly penetrates the surface. Block all drains and use absorptive coverings to contain run-off or excess material. Use soap and water to remove overspray as soon as possible.

What are the Coverage Rate(s):
100 - 150 square feet per gallon on concrete. Note: coverage rates will vary based on the porosity of the substrate.

Product Limitations:
Not suitable for use over asphalt surfaces. This product is designed for use on horizontal or vertical surfaces. Do not use on below-grade surfaces that are subject to severe hydro-static pressures. When using in areas subjected to hot tire traffic, allow adequate time for product to cure before putting the area back into surface. When applying over previous coating, hot tire resistance maybe compromised. Do not use if the area will be exposed to softer, high performance tires.

How Long to Wait:
One to two hours, depending on temperature and humidity. Allow 4 - 6 hours cure time before exposing to foot traffic. Allow 4 days cure time before exposure to heavy traffic, such as forklifts, automobiles, etc. If applying a finish wax, allow 48 hours cure time before waxing.

About Waxing:
For best long-term results on interior surfaces, when cured, MasonrySaver Decorative Concrete Sealer should be sealed and protected with a stamped concrete waxing compound, such as MasonrySaver #25 Floor Finish®. Failure to apply and maintain a wax coating will result in premature failure of the product. On exterior surfaces no wax coating is necessary.

Safety Precautions to Observe:
Proper safety procedures should be followed at all times when handling chemical products. Always wear chemical resistant gloves and chemical splash goggles. 

Refer to the Material Safety Data Sheet for specific safety information regarding this product.

 
  Worth Quoting...  
     
  " After cleaning with an acid cleaner, or following the application of an acid-based concrete stain, it is extremely important to rinse the surface thoroughly to bring the substrate to a neutral ph level (7). Testing with ph paper should be done prior to sealing to insure that a neutral ph has been achieved. Applying sealer over an acidic substrate will most likely result in failure. "  
Copyright (c) 2002 - 2014 Small's Hardware Inc. All rights reserved. Privacy Notice | Contact Us
All trademarks and registered marks are the property of their respective owners.
DTEP is a registered trade name of Small's Hardware Inc. State of Ohio
Mailing Address • 109 S Wayne Ave • Lockland OH • 45215
Visit our StoreFront