buy RemovALL 520 High Performance Coatings Remover online

     
 

View all products by this Manufacturer

 
 
  • RemovALL 520 is no longer available in the US / Canada. see similiar
 
  Item: RemovALL 520 High Performance Coatings Remover
 
 
  Size: 5-gallon
 
 
  Appearance: Blue foamed emulsion
 
 
  VOC Content: 70 g/L • 0.58 Lbs./Gal.  
     
  Case Pack: single 5-gallon pail.
 
 
  UPC Code: N/A  
  Quick Product Facts  
     
 

RemovALL™ 520 High Performance Coatings Remover is a water-based paint stripper that is biodegradable, user-friendly and environmentally safe. It is extremely effective in removing 2-component high performance coatings used in automobile and heavy industrial applications:

  • Water-based.
  • Fully biodegradable.
  • Non-flammable.
  • Contains no TAPs or HAPs.
  • Non-carcinogenic.
  • Easily cleans up with running water.
  • Low VOCs.
  • Non-ozone-depleting.
  • Not regulated by authorities for transportation.
 
     
 

 

 
 
  RemovALL™ 520 High Performance Coatings Remover
 
 
 

buy RemovALL 520 High Performance Coatings Remover onlineTypical Uses:
RemovALL™ 520 High Performance Coatings Remover has proven to effectively lift highly cross-linked urethane and epoxy top coats and primers, alkyds, non-skid coatings (100% solid content) and the toughest of industrial coatings and linings from metallic and plastic substrates. It is also capable of lifting fuel resistant primers, and coal tar epoxies.

Coverage:
Coverage is approximately 40 to 90 sq.ft./ US Gal. (1 to 2.2 sq.m./L) depending on substrate and coating to be removed.

Optimum Temperature:
Surface temperatures should be 65 to 95°F (20 to 32°C). The product performs effectively at lower temperatures - even at 32°F (0°C), but the dwell time increases.

Dwell Time:
The time required for penetration varies according to the type of paint, the thickness of the paint, and the temperature.

Most paint systems require between 2 to 36 hours. RemovALL™ 520 High
Performance Coatings Remover can be left overnight, but do not allow
product to dry out.

Equipment & Tools:
This product is engineered for spray application.

Airless sprayers are recommended. Use only airless equipment with
chemical resistant packing, such as a Hero 85 SEL or larger pump. A
typical medium size airless sprayer is capable of spraying this product.

Equip the sprayer with a tip size of 0.019 inches or larger.

(Example: a 519 or 425 tip). Other equipment: brushes, rollers, scraper, masking tape, plastic (polyethylene) sheet, pressure washer, electric drill with mixer,
empty pails for clean-up, running water, rags.

Roller application should be used only for horizontal surfaces.

Safety Precautions:
Proper safety procedures should be followed at all times while handling the product.  Refer to the Material Safety Data Sheet for important health / safety information before use.

 
 

When there are multiple layers of paint, it is possible that there is poor inter-coat adhesion between some layers. Premature lifting may occur at this interface.  If this happens, remove the lifted layers and re-apply the stripper. Do not rinse with water between applications.

Do not allow the stripper to dry out. The stripper is designed to remain wet and effective over extended periods of time (up to 48 hours), but excessive sunshine, windy conditions or insufficient stripper thickness can cause early drying.  If the stripper starts to dry, re-apply a light coating and allow extra time for completion.

 
Copyright (c) 2002 - 2015 Small's Hardware Inc. All rights reserved. Privacy Notice | Contact Us
All trademarks and registered marks are the property of their respective owners.
DTEP is a registered trade name of Small's Hardware Inc. State of Ohio
Mailing Address • 109 S Wayne Ave • Lockland OH • 45215
Visit our StoreFront